Global trade fair insights

List of catalogs of this article:

• 1、Global trade fair insightsHow to disassemble and install the engine cylinder head
• 5, What is the type of cylinder head?
• 6. What are the types of cylinder heads for car engines? What are their advantages and disadvantages? What kind of hair is each used for...

Is the engine cylinder block and cylinder head cast?

1. The engine cylinder head is an important part, usually made of cast iron or aluminum alloy. Its main function is to close the cylinder and install the valve and piston.At the same time, it also has to withstand the high temperature and high pressure inside the cylinder, which has the functions of protecting the valve and piston, stabilizing the cylinder temperature, reducing noise and so on.

2. Casting and molding: engine body, cylinder head, clutch shell, drive rear axle. Forged type: crankshaft, semishaft, camshaft, connecting rod, valve top rod. The difference between hub forging and casting is that the production and processing methods are different.

3. Therefore, it is obviously illogical to say that EA888 uses cast iron to reduce costs. Secondly, EA888 is not all cast iron, the cylinder head is aluminum, and the cylinder block is cast iron. If the cost is controlled, it should be all cast iron. Why is the cylinder head is made of aluminum, and the cylinder block is made of cast iron. In short, Volkswagen EA888 series The cast iron engine is not used for lowering the engine.

4. The engine is composed of two major parts, the cylinder block and the cylinder head, which are connected to each other by bolts.Alloy cast iron is commonly used as engine cylinder block materials, but cast iron has many innate shortcomings, such as heavy weight, poor heat dissipation, high friction coefficient, etc. Therefore, more and more engine cylinder blocks are made of aluminum alloy.

5. Most pickup trucks will use diesel engines, because diesel engines have stronger torque and higher fuel economy. However, some pickup trucks use gasoline engines. The engine adopts in-cylinder direct injection technology, aluminum alloy cylinder head and cast iron cylinder block.

What are the components of the cylinder head?

The cylinder head is composed of a water sleeve, a valve and a cooling sheet, an inlet and exhaust gate seat holes, a valve duct hole, a spark plug mounting hole (gasoline engine) or an injector mounting hole (diesel engine). VapourThe cylinder head is made of cast iron or aluminum alloy, which is the installation base of the valve mechanism and the sealing cover of the cylinder. The good cylinder and the top of the piston form the combustion chamber.

The cylinder head is one of the important parts of the engine. It is composed of water sleeve, valve and heat sink, intake valve seat hole and exhaust valve seat hole, valve duct hole, spark plug mounting hole (or injector installation hole). Its main function is to seal the cylinder, form a combustion space with the piston, and withstand the action of high-temperature and high-pressure gas.

Cylinder head body: made of cast iron or cast aluminum and other materials, and accessories such as camshaft, valve and fuel injector are installed on it. Gale seat: support the valve and connect it to the cylinder head body through the valve seat. Spark plug hole: assemble the spark plug, ignite to generate sparks and ignite the fuel.

The following is on the cylinder headIntroduction to the composition structure: Basic composition: on the cylinder head, there are intake and exhaust gate seat holes, valve duct holes and spark plug mounting holes (gasoline engine) or injector installation holes (diesel engine). Some cylinder heads also have water inlet, exhaust dube and part of the combustion chamber or combustion chamber.

cylinder block cylinder head positioning difference

The difference between the engine cylinder head is that the cylinder block is equipped with pistons, crankshafts, oil pumps and other parts, which is called the cylinder block. The cylinder head is installed on the cylinder block, and the intake and exhaust system is installed in the cylinder head. Engine balding refers to all electrical generators and brackets, distributors, high-voltage wires, spark plugs, ECUs, etc. and oil injection systems.

Cylinder head crack inspection Paint the surface of the cylinder head for defect inspection. For aluminum cylinder heads, spray a special dye on the parts, and then spray the chemical developer. The developer turns the dye in the crack red and makes the crack appear.

In actual use, there is not much difference between the two cylinder blocks. All-aluminum engines have only been available in recent years. The previous engines were all cast iron. The service life of a cast iron engine is exactly the same as that of an aluminum cylinder engine.Please feel free to use it. The difference between cast iron and aluminum alloy of engine cylinder block is the difference in net weight and capacity.

How to disassemble and install the engine cylinder head

The steps for disassembly and installation of the engine cylinder head are as follows: the order of disassembly and installation of the cylinder head bolts is carried out according to the sequence diagram of tightening the cylinder head and the sequence of the loose cylinder head tightening bolts; when installing the cylinder head, it should be more Replace all sealing strips or sealing gaskets, and pay attention to the installation position of the gasket.

First, remove the cylinder head of the Seahorse car engine, turn off the ignition switch, and remove the battery ground wire. Empty the antifreeze and unplug the antifreeze hose from the connecting tube on the cylinder head. Secondly, remove the upper part of the intake manifold and block the inlet pipe on the cylinder head with a clean cloth.

Remove the gasoline pump, so that the external components of the engine are basically disassembled.Disassemble the fuselage components according to the following requirements 1) Remove the fixing screw of the cylinder head, note that the screw should be crossed and loosened from both ends to the middle, and the screw should be removed three times. 2) Lift the cylinder head. 3) Remove the cylinder pad and pay attention to the installation direction of the cylinder pad.

Turn off the ignition switch and remove the battery ground wire. Discharge the coolant and unplug the coolant hose from the connecting tube on the cylinder head. ( 2) Remove the upper part of the intake manifold and block the inlet pipe on the cylinder head with a clean cloth. ( 3) Remove the spark plug and release the clamp of the high-pressure ignition line, as well as the guard of the fuel injection valve.

What is the type of cylinder head?

1. The cylinder head of the water-cooled engine has three structural forms: integral, block and monomer.

2. The structure of the cylinder head is as follows: if all cylinders share a cylinder head, the cylinder head is called an integral cylinder head; if there is one cover for each two cylinders or one cover for three cylinders, the cylinder head is a block cylinder head; if there is one cylinder head for each cylinder, it is a monomer cylinder head; if the air-cooled engine is a single cylinder head.

3. Convenient disassembly and installation; monomer type: convenient casting, conducive to serialization, universalization, and easy to guarantee the unstiness of combined surface processing. The cylinder head of the water-cooled engine has three structural forms: integral, block and monomer. There are 2 types of engine cylinder heads. One is water as the medium, and the other is air-cooled with a heat sink.

4. The type of engine cylinder head varies according to the number of cylinders, the number of valves and the layout. For example, a single-cylinder engine usually has only one valve and one spark plug, while a six-cylinder engine may have 24 valves.

5. In a multi-cylinder engine, if all cylinders share a cylinder head, the cylinder head is called an integral cylinder head; if there is one cover for each two cylinders or one cover for three cylinders, the cylinder head is a block cylinder head; if there is one cylinder head per cylinder, it is a single cylinder head. Air-cooled engines are all monomer cylinder heads.

What are the types of cylinder heads for car engines? What are their advantages and disadvantages? What kind of hair is it used for...

1. In-line: The advantage is that the structure is simple and the cost is low, so most of the small displacement is in-line, and the disadvantage is that the vibration is large. V-type: The advantage is that it has a compact structure and good stability. The disadvantage is that it is more expensive than the in-line type, which is suitable for large displacement.

2. The cylinder head of the water-cooled engine has three structural forms: integral, block and monomer. The function of the cylinder head is to seal the cylinder, form a combustion space with the piston, and withstand the effect of high-temperature and high-pressure gas.

3. In-line engine In-line engine refers to the arrangement of engine cylinders in a straight line, and all cylinders are arranged side by side at the same angle into a plane.