Trade flow analysis software

List of the table of contents of this article:

• 1,How to connect the prousb door lock system with the access control system
• 2, How to set the time of proUSB door lock software
• 3、prousb door lock how to set a new door card
• 4,Trade flow analysis software Why can't the guest card swiped by the prousb door lock system open the door

prousb How to dock the door lock system with the access control system

1. The line from the electric lock to the controller, if the length of the line is less than 50 meters, it is required to use the cross-sectional area 1" method: Select "Controller" in "Basic Settings", which is helpful to find TC Communication failure of P/IP controller. Indicator light judgment method: CPU indicator light: When it is normal, the CPU indicator light flashes.

2. In AnBefore installation, first understand the structure network, function and network design of the entire access control system, and use RS485 network method or TCP/IP network method. Install the card reader display. Install the door opening button. Debug the system to ensure the use of the access control system.

3. How to set up a new door card for prousb door lock: find the "management card" on the Prousb door lock and use the management card to open the door lock. Place the new door card in the reading area on the door lock, and the door lock will make a "tick" sound, indicating that the door card has been recognized. Use the management card again to open the door lock and enter the setting interface of the door lock.

4. After installing the prousb door lock system, click the software icon on the desktop to run the software. Operator login screen: the default work number is Admin, and there is no password.

5. The +12V and GND terminals (power supply of the access control host) on the access control host are connected to the +12V and GND terminals of the access control power supply. The front end of the electronic control lock is connected to the NO or NC end of the access control power supply (depending on the normal opening and closing); the usual connection method is connected to the NC end (power-on unlocking, power-off lock). The negative end of the electronic control lock is connected to the GND end of the access control power supply.

How to set the time of proUSB door lock software

Make an authorization card, touch the room three times, and then touch it with the room card to automatically set the door lock time.

Xiaomi smart door lock time setting 1 confirm the administrator's fingerprint. Press the "B" key on the fingerprint lock to activate the fingerprint lock, and then press the administrator's finger in the fingerprint window. Hear "With a click, [menu] will be displayed on the display screen. If there is a fingerprint error, you will hear three "tick" sounds... 2 Enter the setting interface.

Cadiz k20pro If you want to set the anti-lock time, you can follow the steps below: open the Cadiz APP and enter the door lock management page. Click the "Settings" button to enter the door lock setting page. Find the "Anti-Lock Time" option on the setting page and click to enter.

The steps to adjust the locking time of Cadiz Z1Pro are as follows: open the mobile phone APP, enter the "Door Lock" page, and select "Cadiz Z1Pro". On the door lock page, select "Locking Time". On the lock time page, select the time range that needs to be adjusted, such as "the same day", "the day before" or "within a week".

Set the date and enter the management mode of the fingerprint lock.Press [2] to enter the system settings, and then press [2] to enter the date setting interface. Set the time and enter the management mode of the fingerprint lock. Press [2] to enter the system settings, and then press [1] to enter the time setting interface.

How to set up a new door card for prousb door lock

1. Jianshu smart fingerprint lock is the card recording step: click the "#" key first, and then enter the administrator's fingerprint. After successful entry, click the "#" key to verify Enter the management page of the certificate fingerprint, find the IC card settings, and then click the "#" key to enter. After entering, you can see that the IC card has been added, and then click the "#" key to add it.

2. Enter the wallet app in the mobile phone and select"Door Card", and then click "Add" on the right side of the physical door card and put the Xiaomi smart lock close to the NFC area. In the pop-up window, click to continue reading the content of the card, and put the Xiaomi smart lock close to the NFC area, then enter the card name, select the card, and click Done.

3. Operation steps: open the battery cover. Press the setting key to make a ticking sound. Press the start key (located one place after the number 3 on the keyboard), enter the password (3-8 digits) and press the # key. There was a ticking sound, and the operation was successful. How to set up a smart door lock - door opening card, password, fingerprint lock, remote control settings Operation steps: open the battery cover.

4. Solution: Make a time card first to brush it to see if it returns to normal. If not, initialize the door lock again and reset it. [ Expansion] proUSBThe door lock system is a management software specially tailored for the anti-theft and door lock industries launched by Shenzhen Plande Electronic Technology Co., Ltd.

5. First, swring the mechanical key, the door lock tongue is in a retracted state, and secondly. The blue light of this card is on, and then release the mechanical key. Finally, use the authorization card to forcibly clear the setting information of the door lock room, and you can set up the card printing.

Why can't the guest card brushed by the prousb door lock system open the door

prousb door lock system error prompt 3 sounds: indicates that the door lock is in the anti-lock state (there are two This phenomenon may occur: a. At this time, it may be that the guest is locked in the room and does not want to be disturbed; b. There is a problem with the anti-lock micro-control switch in the door lock cylinder.) Solution: Reissue the card that can open the anti-lock or repair the anti-lock microcontrol switch.

Power failure: The power supply of the access control system may be faulty or power outage, causing the door to be unable to open. In this case, it is necessary to check whether the power supply of the access control system is normal and repair it in time. Door lock failure: The door lock may be faulty or damaged, causing the door to be unable to open.

Possible reasons are (1) the guest card does not match the address of the door lock. Handling measures: detect whether the room number of the guest card matches the address of the door lock, and detect whether the floor area of the management card matches the address of the door lock.

First, the electronic lock of the door does not respond: 1. Use the spare mechanical key to unlock; 2. Replace the battery circuit board. Second, the magnetic card reacts but cannot open the door: 1. Use a spare electronic key or mechanical key to open the lock; 2. Connect the plug or replace the battery.