global goods transport

List of the table of contents of this article:

• 1、Design of remote temperature control system based on PLC: Design paper of temperature control system
• 2, Elevator Control Technology Paper (2)
• 3, Graduation paper on temperature and humidity control system based on 51 single-chip microcomputer
• 4, Paper on single-chip microcomputer temperature control system

PLC-based remote temperature controlSystem design: temperature control system design paper

so that the quality of the product can be greatly improved. Therefore, intelligent temperature control technology is being widely applied. This temperature design adopts the now popular AT89C51 single-chip microcomputer as the controller, uses the PID control method, and is equipped with other circuits to control the water temperature of the water heater.

The precision temperature control system based on single-chip microcomputer digital PID control designed in this paper has achieved good control effect in practical application, and the temperature control accuracy reaches ±0.1℃.

This paper designs a temperature measurement and control device based on MSP430 single-chip microcomputer, which can measure the ambient temperature, and can give the adjustment amount according to the given temperature value, control the actuator, and achieve the purpose of regulating the ambient temperature.1 Overall scheme design Single-chip microcomputer temperature control system takes MSP430 single-chip microcomputer as the control core.

In response to the call of innovative enterprises of electromechanical companies and automation branches, I am now developing a "digital analog signal generator" and "heat treatment temperature control system" based on single-chip microcomputers. The former should be given the debugging of the on-site instrument and the PLC analog signal, and the latter will be applied to the heat treatment of on-site machinery and equipment installation.

The automated measurement and control of the industrial production process almost mainly relies on various sensors to detect and control various parameters in the production process, so that the equipment and system can operate normally in the best state, so as to ensure the high efficiency and high quality of production. 1 Selection of temperature sensor Scheme 1: Adopt thermal resistance temperature sensor.

Elevator Control Technology Paper (2)

1. In electricity In the troubleshooting of ladder faults, the control system can quickly analyze the types of faults and improve the stability of the elevator by entering fault data. Intelligent control. Intelligent control is the second largest type of intelligent technology in the elevator control system.It mainly includes two major components: "processing unit" and "system application". The first is the processing unit.

2. PLC control replaces traditional relay control. PLC is a new automatic control device integrating computer control, automatic control technology and communication technology.

3. Graduation design (thesis) opening report The purpose and significance of topic selection: In modern society, elevators have become indispensable transportation equipment. The existence of elevators makes the transportation of each high-rise building more convenient.

4. DCS can be interpreted as an automated high-tech product that is widely used in industries with more analog loop control. It tries to distribute the dangers caused by control and centralizes management and display functions. DCS is generally composed of fivePart composition: 1: Controller 2: I/O board 3: Operation station 4: Communication network 5: Graphics and travel software.

5. PLC control of the four-story elevator PLC electrical control of double constant pressure towerless water supply Graduation thesis Chapter 1: Design requirements Receive and register all the instruction signals of the elevator outside the floor, and register and output the registration signal.

6. In addition, the model that replaces the relay control system with a programmable controller is still promising to control the single ladder.

Research graduation thesis on temperature and humidity control system based on 51 single-chip microcomputer

The second part is the design of the overall scheme of the system, which is mainly determined by comparing the centralized scheme. The best solution to use.The third part is the introduction of the main unit circuit, including temperature measurement and control circuit, humidity measurement and control circuit, digital display circuit, alarm circuit, peripheral circuit of 51 single-chip microcomputer, etc.

Chapter 1 Hardware Circuit Analysis Section 1 Hardware Circuit Overview The temperature measurement system consists of five parts: power supply module, detection module, display module, control module and communication module.

This paper designs a temperature measurement and control device based on MSP430 single-chip microcomputer, which can measure the ambient temperature, and can give the adjustment amount according to the given temperature value, control the actuator, and achieve the purpose of regulating the ambient temperature. 1 Overall scheme design Single-chip microcomputer temperature control system takes MSP430 single-chip microcomputer as the control core.

Based on MCS-51 single-chip microcomputer temperature control systemNumber of texts on the resistance furnace: 1725 Pages: 42 Paper number: JD471 Abstract In recent years, with the penetration of computers in the social field, the application of single-chip microcomputers is constantly deepening, while driving the renewal of traditional control detection day by day.

The temperature measurement system based on 51 single-chip microcomputer Abstract: Single-chip microcomputers are widely used in detection and control systems, and temperature is a quantity that the system often needs to measure, control and maintain.

Paper on single-chip microcomputer temperature control system

1. Single-chip microcomputer temperature control system takes MSP430 single-chip microcomputer as the control core. The hardware part of the whole system includes temperature detection system, signal amplification system, A/D conversion, single-chip microcomputer, I/O equipment, control execution system, etc.

2. The temperature and humidity control system designed this time can use single-chip microcomputers to detect and analyze the collected temperature and humidity data in real time, and make timely judgments, so as to realize the intelligence and automation of temperature and humidity control.

3. Donghua University of Technology Graduation Design (Thesis) Water Heater Temperature Control Based on Single-chip Computer Abstract Temperature is an indispensable physical quantity in daily life, and temperature has positive significance in various fields.

4. Section 1 Hardware Circuit Overview The temperature measurement system consists of five parts: power supply module, detection module, display module, control module and communication module.

5. Abstract: Single-chip microcomputers are widely used in detection and control systems. Temperature is a quantity that the system often needs to measure, control and maintain.This paper introduces the design of the AT89C2051 single-chip microcomputer temperature control system from both hardware and software aspects, and briefly describes the hardware schematic diagram and program block diagram.

6. In the single-chip microcomputer application system of real-time detection and automatic control, the single-chip microcomputer is often used as a core component. Single-chip microcomputers were born with the development of ultra-large-scale integrated circuit technology. Because it has the characteristics of small size, strong function and high cost performance.