The card reader is used to read the smart card information of the swiper ( Card number), and then convert it into an electrical signal and send it to the access control controller. According to the received card number, the controller judges through the software whether the cardholder has been authorized to enter the gate during this period of time, and completes the unlocking, maintaining the lock and other work according to the results of the judgment.
RealAt present, a variety of applications other than the access control system include electronic payment parking lot management, computer desktop login system, elevator operation and other applications. Through the open access control architecture, it realizes seamless upgrades and provides different upgrade options for the future.
There are several ways to solve the encrypted access control card: Replace the IC access control card: This is the simplest and most effective way to ensure the security of the access control system.
Enter the programming mode: press [*]+[6-bit programming password], beep twice, (the red light flashes, the green light is on. The factory programming password is 990101. Users must modify this programming password after enabling the access control device. If there is no programming instruction within 20 seconds, the system will automatically exit the programming state.
Expand content: except for the encryption gateCard ban, modern access control system can also support other security authentication methods, such as mobile phone Bluetooth door opening, QR code recognition, etc. The introduction of these technologies has further improved the convenience and security of the access control system.
According to the master key of the card issuing unit, the card issuing unit shall load the personal basic information files and application files of the unit, and print photos, names, etc. on the surface. In this way, the cards that have been personalized can be sent to the cardholder.
can be sent through the software to report the lost card The original function system of the elevator will automatically release the control of the elevator in the event of a power failure or system failure to restore the original function of the elevator.
You only need to bring your valid ID card to the account opening bank to report the loss directly. The bank staff will check the basic information according to the ID card number and find out the bank card number and other information.
Apply for loss at the customer service department of the IC card sales center. The procedures are as follows: A card: bring the original ID card or household registration book, pay a deposit of 18 yuan, and pick up the card with the loss report document three days later (A card without ID number cannot be reported lost).B card: bring the original ID card or household registration book, and go through the refund procedures with the loss report document three days later.
Bank of China. To report the loss verbally, you need to check the ID number, the name of the account opening bank, the account opening date and other information. When reporting the loss in writing, you need to bring your original ID card to fill in the application form for reporting the loss. China Merchants Bank. Orally report the loss by telephone, mobile banking, online banking or any branch of the bank, which is valid for 5 days.
1. Elevator IC card management system Intelligent IC card control elevator management system is controlled by IC cards installed in the elevator car and outside the hall.It consists of the instrument, the IC card issuance center installed in the management center, and the IC card held by the elevator users.
2. Security of the system. Elevator swipe card and IC card systems need to have a high degree of security to prevent illegal intrusion and malicious operations. When installing the system, it is necessary to carefully check all links of the system to ensure that it has a high degree of security and reliability. Privacy protection of users.
3. The intelligent IC card elevator elevator control system, that is, the IC card layer-controlled elevator control system, is the intelligent control system that takes over the original elevator system button through passive contacts. It is installed in the car. Only by using the IC card can you reach the floor you want to go to. You can swipe the card directly, no need to press the button, and the password to take the elevator.
4. Shenzhen Wanglong tells you about the principle and types of IC card elevators.: The intelligent IC card control elevator management system consists of the IC card controller installed in the elevator car and outside the hall, the IC card issuance center installed in the management center, and the IC card held by the elevator users.
The full name of the elevator control system is intelligent elevator IC card control system. The elevator control system is an IC card controller installed outside the elevator car and hall, installed in the management center. It is composed of IC cards held by users of IC card issuing centers and elevators.
What does the ladder control system mean? The so-called "ladder control" means that a device similar to "en access control" is installed on the original elevator. As long as you brush it once, it will automatically turn on and take the user to the floor you want to reach.
The ladder control system, also known as the intelligent elevator control system, is an intelligent management system that adopts advanced card reading and writing technology, automatic control technology and sensing technology, and uses the computer network platform to comprehensively automate the use of elevators.
Prospect photoelectric elevator IC card - economical configuration: main controller I smart card II main functions: 1 swipe the card to use the elevator; 2 shield idle personnel; 3 VIP floor control 4 convenient installation, fast debugging, convenient use.
The card reading module and the function expansion module constitute the elevator control unit. After the cardholder reads the card in the elevator, the system allows the cardholder to reach the authorized floor according to the prior settings. If the cardholder operates the unauthorized floor button, the elevator will not respond.Non-cardholders cannot operate the elevator.
The elevator IC card swipe system should be to control the use of the elevator (that is, it cannot be used by unrelated personnel, or it can be used for a fee), that is, it can only be used by swiping the elevator, and the installation method should have an installation instruction manual.
1. What does the escalator control system mean? The so-called "escalator control" means that a device similar to "enter control" is installed on the original elevator. As long as you brush it once, it will automatically turn on and Users take them to the floor they want to reach.
2. For the wiring principle of elevator card swipe and elevator IC card system, it generally needs to be operated according to the specific brand and model. It is recommended that you check the corresponding product manual and installation guide first.Generally speaking, the elevator swipe card and IC card system need to be connected with the elevator control system to realize the control and permission management of the elevator switch.
3. Elevator IC card controller is a high-tech product that takes IC and ID as information carriers and integrates information management, computer and smart card technology, which can control access and exit. It brings convenience to people's lives. It has a variety of functions of authorization, recording, query, statistics, anti-theft, alarm light, and has extremely high security capabilities.
4. The intelligent IC card elevator elevator control system, that is, the IC card layer-controlled elevator control system, is an intelligent control system that takes over the original elevator system button through passive contacts. It is installed in the car. Only by using the IC card can you reach the floor you want to go to. You can swipe the card directly without pressing the button, and the password to take the elevator.
5. The elevator IC card swipe system should be to control the use of the elevator (that is, it cannot be used by unrelated personnel, or it can be used for a fee), that is, the swipe card elevator can only be used, and the installation method should be installed using the installation manual.
6. Non-contact elevator IC card control system scheme Project introduction According to the actual situation and needs, the requirements of the whole project are as follows: (1) There are 2 office buildings and 10 elevators, which must be a ladder control system (swipe the card to the designated floor) (2) Equipped with 10 sets of ladder control systems (3) ladder The control system adopts the network mode.
1. The elevator IC card swipe system should be to control the use of the elevator (that is, it cannot be used by unrelated personnel, or it can be used for a fee), that is, it can only be used by swiping the elevator, and the installation method should have the installation instruction manual.
2. The installation method of the IC card elevator equipment of the ic card elevator is as follows: the ladder control and the elevator button signal line adopt the dry contact method, which does not change the original circuit of any elevator, and has no impact on the daily work of any brand elevator.
3. There are two installation methods for elevator IC cards: open installation and hidden installation. The open installation is simple, the installation cost is low and easy to operate. The disadvantage is that the prominent panel affects the beauty.
4. The wiring of different systems is different, and the wiring methods of layered control and unified control are also different, oftenThe wiring method shown is to string the output end of the card reader into the signal public end of the elevator button, and then set up the card reader. The setting method of card reader equipment of different manufacturers is different. Please refer to the random instruction manual.
5. Control method 1: Control the elevator call button outside the elevator. This control mode is to install a card reader outside the elevator, that is, at the elevator entrance of the elevator hall, and connect the elevator controller. When the user swipes the card effectively, the elevator summoning button can be activated, and the floor button in the elevator bridge box can be activated, and the user can use it. Elevator.
US-China trade data comparisons-APP, download it now, new users will receive a novice gift pack.
The card reader is used to read the smart card information of the swiper ( Card number), and then convert it into an electrical signal and send it to the access control controller. According to the received card number, the controller judges through the software whether the cardholder has been authorized to enter the gate during this period of time, and completes the unlocking, maintaining the lock and other work according to the results of the judgment.
RealAt present, a variety of applications other than the access control system include electronic payment parking lot management, computer desktop login system, elevator operation and other applications. Through the open access control architecture, it realizes seamless upgrades and provides different upgrade options for the future.
There are several ways to solve the encrypted access control card: Replace the IC access control card: This is the simplest and most effective way to ensure the security of the access control system.
Enter the programming mode: press [*]+[6-bit programming password], beep twice, (the red light flashes, the green light is on. The factory programming password is 990101. Users must modify this programming password after enabling the access control device. If there is no programming instruction within 20 seconds, the system will automatically exit the programming state.
Expand content: except for the encryption gateCard ban, modern access control system can also support other security authentication methods, such as mobile phone Bluetooth door opening, QR code recognition, etc. The introduction of these technologies has further improved the convenience and security of the access control system.
According to the master key of the card issuing unit, the card issuing unit shall load the personal basic information files and application files of the unit, and print photos, names, etc. on the surface. In this way, the cards that have been personalized can be sent to the cardholder.
can be sent through the software to report the lost card The original function system of the elevator will automatically release the control of the elevator in the event of a power failure or system failure to restore the original function of the elevator.
You only need to bring your valid ID card to the account opening bank to report the loss directly. The bank staff will check the basic information according to the ID card number and find out the bank card number and other information.
Apply for loss at the customer service department of the IC card sales center. The procedures are as follows: A card: bring the original ID card or household registration book, pay a deposit of 18 yuan, and pick up the card with the loss report document three days later (A card without ID number cannot be reported lost).B card: bring the original ID card or household registration book, and go through the refund procedures with the loss report document three days later.
Bank of China. To report the loss verbally, you need to check the ID number, the name of the account opening bank, the account opening date and other information. When reporting the loss in writing, you need to bring your original ID card to fill in the application form for reporting the loss. China Merchants Bank. Orally report the loss by telephone, mobile banking, online banking or any branch of the bank, which is valid for 5 days.
1. Elevator IC card management system Intelligent IC card control elevator management system is controlled by IC cards installed in the elevator car and outside the hall.It consists of the instrument, the IC card issuance center installed in the management center, and the IC card held by the elevator users.
2. Security of the system. Elevator swipe card and IC card systems need to have a high degree of security to prevent illegal intrusion and malicious operations. When installing the system, it is necessary to carefully check all links of the system to ensure that it has a high degree of security and reliability. Privacy protection of users.
3. The intelligent IC card elevator elevator control system, that is, the IC card layer-controlled elevator control system, is the intelligent control system that takes over the original elevator system button through passive contacts. It is installed in the car. Only by using the IC card can you reach the floor you want to go to. You can swipe the card directly, no need to press the button, and the password to take the elevator.
4. Shenzhen Wanglong tells you about the principle and types of IC card elevators.: The intelligent IC card control elevator management system consists of the IC card controller installed in the elevator car and outside the hall, the IC card issuance center installed in the management center, and the IC card held by the elevator users.
The full name of the elevator control system is intelligent elevator IC card control system. The elevator control system is an IC card controller installed outside the elevator car and hall, installed in the management center. It is composed of IC cards held by users of IC card issuing centers and elevators.
What does the ladder control system mean? The so-called "ladder control" means that a device similar to "en access control" is installed on the original elevator. As long as you brush it once, it will automatically turn on and take the user to the floor you want to reach.
The ladder control system, also known as the intelligent elevator control system, is an intelligent management system that adopts advanced card reading and writing technology, automatic control technology and sensing technology, and uses the computer network platform to comprehensively automate the use of elevators.
Prospect photoelectric elevator IC card - economical configuration: main controller I smart card II main functions: 1 swipe the card to use the elevator; 2 shield idle personnel; 3 VIP floor control 4 convenient installation, fast debugging, convenient use.
The card reading module and the function expansion module constitute the elevator control unit. After the cardholder reads the card in the elevator, the system allows the cardholder to reach the authorized floor according to the prior settings. If the cardholder operates the unauthorized floor button, the elevator will not respond.Non-cardholders cannot operate the elevator.
The elevator IC card swipe system should be to control the use of the elevator (that is, it cannot be used by unrelated personnel, or it can be used for a fee), that is, it can only be used by swiping the elevator, and the installation method should have an installation instruction manual.
1. What does the escalator control system mean? The so-called "escalator control" means that a device similar to "enter control" is installed on the original elevator. As long as you brush it once, it will automatically turn on and Users take them to the floor they want to reach.
2. For the wiring principle of elevator card swipe and elevator IC card system, it generally needs to be operated according to the specific brand and model. It is recommended that you check the corresponding product manual and installation guide first.Generally speaking, the elevator swipe card and IC card system need to be connected with the elevator control system to realize the control and permission management of the elevator switch.
3. Elevator IC card controller is a high-tech product that takes IC and ID as information carriers and integrates information management, computer and smart card technology, which can control access and exit. It brings convenience to people's lives. It has a variety of functions of authorization, recording, query, statistics, anti-theft, alarm light, and has extremely high security capabilities.
4. The intelligent IC card elevator elevator control system, that is, the IC card layer-controlled elevator control system, is an intelligent control system that takes over the original elevator system button through passive contacts. It is installed in the car. Only by using the IC card can you reach the floor you want to go to. You can swipe the card directly without pressing the button, and the password to take the elevator.
5. The elevator IC card swipe system should be to control the use of the elevator (that is, it cannot be used by unrelated personnel, or it can be used for a fee), that is, the swipe card elevator can only be used, and the installation method should be installed using the installation manual.
6. Non-contact elevator IC card control system scheme Project introduction According to the actual situation and needs, the requirements of the whole project are as follows: (1) There are 2 office buildings and 10 elevators, which must be a ladder control system (swipe the card to the designated floor) (2) Equipped with 10 sets of ladder control systems (3) ladder The control system adopts the network mode.
1. The elevator IC card swipe system should be to control the use of the elevator (that is, it cannot be used by unrelated personnel, or it can be used for a fee), that is, it can only be used by swiping the elevator, and the installation method should have the installation instruction manual.
2. The installation method of the IC card elevator equipment of the ic card elevator is as follows: the ladder control and the elevator button signal line adopt the dry contact method, which does not change the original circuit of any elevator, and has no impact on the daily work of any brand elevator.
3. There are two installation methods for elevator IC cards: open installation and hidden installation. The open installation is simple, the installation cost is low and easy to operate. The disadvantage is that the prominent panel affects the beauty.
4. The wiring of different systems is different, and the wiring methods of layered control and unified control are also different, oftenThe wiring method shown is to string the output end of the card reader into the signal public end of the elevator button, and then set up the card reader. The setting method of card reader equipment of different manufacturers is different. Please refer to the random instruction manual.
5. Control method 1: Control the elevator call button outside the elevator. This control mode is to install a card reader outside the elevator, that is, at the elevator entrance of the elevator hall, and connect the elevator controller. When the user swipes the card effectively, the elevator summoning button can be activated, and the floor button in the elevator bridge box can be activated, and the user can use it. Elevator.
HS code variance across regions
author: 2024-12-24 02:43HS code-based customs broker RFPs
author: 2024-12-24 02:25Industry-specific tariff code reference
author: 2024-12-24 01:06Latin America HS code classification
author: 2024-12-24 00:55Trade analytics for risk mitigation
author: 2024-12-24 00:14Global trade KPI dashboard templates
author: 2024-12-24 02:25Global trade contract verification
author: 2024-12-24 02:21Textile supply chain HS code mapping
author: 2024-12-24 01:46Optimizing distribution using HS code data
author: 2024-12-24 00:59International trade event forecasts
author: 2024-12-24 00:38
HS code-driven demand planning
178.89MB
Check
Import restrictions by HS code category
864.39MB
Check
Soybeans (HS code ) import patterns
533.96MB
Check
Automated customs declaration checks
323.52MB
Check
Sustainable sourcing via HS code tracking
342.85MB
Check
Predictive supply chain resilience
446.94MB
Check
HS code impact on trade finance
839.72MB
Check
Petroleum products HS code insights
223.83MB
Check
HS code-based cost-cutting strategies
484.52MB
Check
Value-added exports by HS code
828.12MB
Check
Raw leather HS code references
353.72MB
Check
Pharma excipients HS code classification
849.57MB
Check
Predictive analytics for supplier risks
447.65MB
Check
Trade data for pharmaceutical imports
859.66MB
Check
Real-time shipment data alerts
353.68MB
Check
GCC HS code-based tariff systems
679.54MB
Check
Supply chain network modeling
981.51MB
Check
Precision instruments HS code verification
759.97MB
Check
How to optimize packaging with trade data
845.51MB
Check
Renewable energy equipment HS code mapping
712.86MB
Check
How to leverage FTA data
156.98MB
Check
HS code-based competitor benchmarking
991.84MB
Check
Global supplier scorecard templates
854.29MB
Check
HS code mapping for duty optimization
733.27MB
Check
HS code-focused compliance audits
399.43MB
Check
HS code-based alternative sourcing strategies
347.45MB
Check
Brazil import export database
328.53MB
Check
Engine parts HS code verification
489.45MB
Check
Industry-wise trade data breakdowns
758.28MB
Check
How to minimize supply chain disruptions
492.71MB
Check
International shipment tracking APIs
385.52MB
Check
Trade data analysis for small businesses
591.54MB
Check
Global trade event monitoring
931.68MB
Check
Automated trade documentation tools
294.35MB
Check
Livestock feed HS code references
923.31MB
Check
How to manage cross-border complexity
241.33MB
Check
Scan to install
US-China trade data comparisons to discover more
Netizen comments More
455 Trade compliance automation tools
2024-12-24 02:36 recommend
478 Surgical instruments HS code classification
2024-12-24 01:31 recommend
2798 Global trade data for currency hedging
2024-12-24 01:22 recommend
659 Biotech imports HS code classification
2024-12-24 00:47 recommend
2764 HS code lookup for global trade
2024-12-24 00:25 recommend