1. You have solved this problem and there are still some problems, that is, the driver. For example, the graphics card and sound card drivers are easy to have problems. If they can't be installed or have problems, Microsoft has stopped developing the corresponding drivers for the XP system. It only depends on whether you are lucky or not.
2. The maintenance department has told you that the XP system cannot be installed, indicating that the motherboard chip is HM86 level and supports the fourth-generation CPU Haswell processor.
3. After power-on, press DEL to enter BIOS, LOAD DEFAULTS SETTINGS, restore the default settings, save and restart 2.
4. Your notebook has not been tested for the XP system before leaving the factory. It is recommended that you do not install the XP system. IT IS RECOMMENDED THAT YOU USE WIN7 OR WIN8 SYSTEM TO GET THE BEST PERFORMANCE AND STABILITY.
5. This is a little complicated. So to speak, the current hard disks are all SATA interfaces, while in the XP system era, the hard disk interfaces are all IDE. That is to say, XP does not recognize the hard disk with SATA interface.
The way to install the XP system on HP notebooks is to disable the SATA local mode to start the laptop. Press the F10 key (or the key specified by the laptop) repeatedly until the laptop enters the Computer Setup interface. Use the arrow keys to select System Configuration.
Change the boot order according to how the computer enters the bios, start the USB disk, and then enter the win8pe system. Select the winxp system gho version in the installation tool, and select the c disk as the system disk. The program will perform the restore operation and click OK.
Now most of the newly released machines use sata hard disks, because the xp system is not integrated with sTherefore, the ata driver needs to be loaded before installing the sata driver to install the xp system normally. However, because it is more troublesome to install the sata driver, it is better not to install the xp system if you do not have to use the xp system.
Your computer has not been officially tested for the XP system when it left the factory. The official cannot guarantee that the machine will be used normally after installing the XP system. It is officially recommended that you use the tested Win7 system.
1. Turn on the computer, start the USB flash drive, and select the win8pe system to enter. Select the gho version of the winxp system and use the c disk as the system disk. Pop-up window, click "OK". Then restart the computer and wait for the computer to release the gho image to complete. Then restart the computer and pop up the installation process of the computer program.
2. Unzip the SATA driver and copy the program in the decompressed folder to the root directory of the floppy disk. ( 2) Put it into the operating system CD-ROM and connectOkay, USB floppy drive, restart the machine, press F9 to enter the boot menu option, use the direction key to select the optical drive, and press Enter to start.
3. If your machine is pre-installed with the Microsoft Windows operating system when you buy it and your machine's operating system is still pre-installed, it is recommended that you try to save important files and restart the machine. When the HP logo appears on the machine, click F11 to restore it with one click. Check the system of the machine to see if it can solve the problem you encountered.
4. How to install the XP system. The first step is to set the light start: the so-called light start means that the computer first reads the optical drive when starting up. In this way, if there is a CD with an optical start function in the optical drive, it can be read out before the hard disk starts (for example, when installing the system from the CD-ROM).
5. The first one: HP's new machine is a graphical version of BIOS, which can be operated with the mouse. Press F10 to enter bios when booting up. In System Configuration---SATA Device Mode, you can select AHCI or IDE here. You can click it with the mouse to select IDE, and then press the "X" button in the lower left corner and select Y. ES.
Change the startup order according to how the computer enters bios, start the USB disk, and then enter the win8pe system, and select the winxp system in the installation tool. Unify the gho version, and select the c disk as the system disk. The program will perform the restore operation, click OK.
The way to install the XP system on HP notebooks is to disable the SATA local mode to start the laptop. Press the F10 key (or the key specified by the laptop) repeatedly until the laptop enters the Computer Setup interface. Use the arrow keys to select System Configuration.
You need to confirm whether these two CDs are XP system CDs. If not, you can look for XP system CDs again.
HS code-driven product bundling strategies-APP, download it now, new users will receive a novice gift pack.
1. You have solved this problem and there are still some problems, that is, the driver. For example, the graphics card and sound card drivers are easy to have problems. If they can't be installed or have problems, Microsoft has stopped developing the corresponding drivers for the XP system. It only depends on whether you are lucky or not.
2. The maintenance department has told you that the XP system cannot be installed, indicating that the motherboard chip is HM86 level and supports the fourth-generation CPU Haswell processor.
3. After power-on, press DEL to enter BIOS, LOAD DEFAULTS SETTINGS, restore the default settings, save and restart 2.
4. Your notebook has not been tested for the XP system before leaving the factory. It is recommended that you do not install the XP system. IT IS RECOMMENDED THAT YOU USE WIN7 OR WIN8 SYSTEM TO GET THE BEST PERFORMANCE AND STABILITY.
5. This is a little complicated. So to speak, the current hard disks are all SATA interfaces, while in the XP system era, the hard disk interfaces are all IDE. That is to say, XP does not recognize the hard disk with SATA interface.
The way to install the XP system on HP notebooks is to disable the SATA local mode to start the laptop. Press the F10 key (or the key specified by the laptop) repeatedly until the laptop enters the Computer Setup interface. Use the arrow keys to select System Configuration.
Change the boot order according to how the computer enters the bios, start the USB disk, and then enter the win8pe system. Select the winxp system gho version in the installation tool, and select the c disk as the system disk. The program will perform the restore operation and click OK.
Now most of the newly released machines use sata hard disks, because the xp system is not integrated with sTherefore, the ata driver needs to be loaded before installing the sata driver to install the xp system normally. However, because it is more troublesome to install the sata driver, it is better not to install the xp system if you do not have to use the xp system.
Your computer has not been officially tested for the XP system when it left the factory. The official cannot guarantee that the machine will be used normally after installing the XP system. It is officially recommended that you use the tested Win7 system.
1. Turn on the computer, start the USB flash drive, and select the win8pe system to enter. Select the gho version of the winxp system and use the c disk as the system disk. Pop-up window, click "OK". Then restart the computer and wait for the computer to release the gho image to complete. Then restart the computer and pop up the installation process of the computer program.
2. Unzip the SATA driver and copy the program in the decompressed folder to the root directory of the floppy disk. ( 2) Put it into the operating system CD-ROM and connectOkay, USB floppy drive, restart the machine, press F9 to enter the boot menu option, use the direction key to select the optical drive, and press Enter to start.
3. If your machine is pre-installed with the Microsoft Windows operating system when you buy it and your machine's operating system is still pre-installed, it is recommended that you try to save important files and restart the machine. When the HP logo appears on the machine, click F11 to restore it with one click. Check the system of the machine to see if it can solve the problem you encountered.
4. How to install the XP system. The first step is to set the light start: the so-called light start means that the computer first reads the optical drive when starting up. In this way, if there is a CD with an optical start function in the optical drive, it can be read out before the hard disk starts (for example, when installing the system from the CD-ROM).
5. The first one: HP's new machine is a graphical version of BIOS, which can be operated with the mouse. Press F10 to enter bios when booting up. In System Configuration---SATA Device Mode, you can select AHCI or IDE here. You can click it with the mouse to select IDE, and then press the "X" button in the lower left corner and select Y. ES.
Change the startup order according to how the computer enters bios, start the USB disk, and then enter the win8pe system, and select the winxp system in the installation tool. Unify the gho version, and select the c disk as the system disk. The program will perform the restore operation, click OK.
The way to install the XP system on HP notebooks is to disable the SATA local mode to start the laptop. Press the F10 key (or the key specified by the laptop) repeatedly until the laptop enters the Computer Setup interface. Use the arrow keys to select System Configuration.
You need to confirm whether these two CDs are XP system CDs. If not, you can look for XP system CDs again.
Predictive container utilization analytics
author: 2024-12-23 23:25Trade data solutions for retail
author: 2024-12-23 23:07HS code compliance for hazardous materials
author: 2024-12-23 22:56USA trade data aggregation services
author: 2024-12-23 22:35HS code segmentation for industrial chemicals
author: 2024-12-23 22:00How to access historical shipment records
author: 2024-12-23 23:08HS code indexing for specialized products
author: 2024-12-23 23:08Customs procedure optimization
author: 2024-12-23 22:51Latin America export data visualization
author: 2024-12-23 22:23527.26MB
Check783.17MB
Check256.75MB
Check968.15MB
Check269.89MB
Check465.28MB
Check958.99MB
Check838.25MB
Check373.27MB
Check927.52MB
Check737.38MB
Check723.44MB
Check949.33MB
Check279.28MB
Check755.77MB
Check921.17MB
Check798.58MB
Check571.43MB
Check444.62MB
Check336.19MB
Check743.79MB
Check559.34MB
Check943.51MB
Check742.78MB
Check234.44MB
Check697.65MB
Check469.15MB
Check439.15MB
Check152.88MB
Check359.64MB
Check961.32MB
Check186.89MB
Check128.91MB
Check951.43MB
Check842.56MB
Check766.13MB
CheckScan to install
HS code-driven product bundling strategies to discover more
Netizen comments More
315 Global supply chain risk assessment
2024-12-24 00:05 recommend
543 HS code indexing for specialized products
2024-12-23 23:46 recommend
2229 Exporter data
2024-12-23 23:31 recommend
1412 HS code mapping to non-tariff measures
2024-12-23 22:31 recommend
1544 HS code metrics for performance dashboards
2024-12-23 22:04 recommend