Hello, reading the fault code 1215, which means that the air flow meter or its line is poor. After testing, the impedance of the air flowmeter does not meet the requirements. After replacing the air flowmeter, the condition of the car improved slightly, but the fault was still there. Check again and find that the 4th cylinder spark plug is covered with gasoline, indicating that the cylinder is not working.
The engine has serious carbon accumulation. The most common cause of idling jitter is excessive carbonisation of the throttle valve or fuel nozzle.
The solutions to unstable idle speed, shaking, shaking and black smoke are as follows: the engine is seriously carbonized. The common cause of car shaking is that the throttle valve is too dirty or the fuel nozzle has too much carbon.Solution: Clean the oil road and check whether there is carbon in the idle motor, which should be cleaned.
The control unit receives the wrong signal and sends the wrong instruction, causing the engine idling intake control to be inaccurate, causing the engine to burn abnormally, which is an indirect cause of unstable idle speed. Common causes are: air flow meter or its line failure; intake pressure sensor or its line failure; engine control unit plug due to poor contact with water inlet or internal computer failure.
Engine ignition order is 2; that is to say, when cylinder 1 is doing work, cylinder 3 is in a compressed state, cylinder 4 is in the intake state, and cylinder 2 is in the exhaust state. Status.
People sit in the cab, and the order of the cylinder is: 5 on the right, and 6 on the left.In this case, the ignition order is: 1-4-5-2-3-6.
The ignition order of the engine is 2; that is, when the 1st cylinder is in the "work", the 3rd cylinder is in the "compression" state, the 4th cylinder is in the "ink-ink" state, and the 2nd cylinder is in the "exhaust" state. Depending on the number of engine cylinders, the ignition order of the engine will also vary.
Engine carbon accumulation problem, the engine will accumulate some carbon accumulation after a period of use, which will cause engine damage, difficulty in starting, poor acceleration, starting The machine is too noisy and other phenomena. Mixed gas combustion is poor and gas combustion is insufficient. Sensor problem. Multiple sensors are aging. If the owner does not add oil as required, it will lead to accelerated engine wear and abnormal operation in the long run, and the engine fault light will turn on. Generally, replacing the oil with the corresponding conditions can eliminate the fault light. The reasons why the engine fault light is on are engine carbonisation problems, poor combustion of mixed gas, sensor problems, maintenance problems and oil quality problems.Car owners need to regularly clean the carbon accumulation of the engine, check the working condition of the sensor, maintain it regularly, and use qualified oil products. The fuel quality is poor and does not meet the standard.
Commodity price indexing by HS code-APP, download it now, new users will receive a novice gift pack.
Hello, reading the fault code 1215, which means that the air flow meter or its line is poor. After testing, the impedance of the air flowmeter does not meet the requirements. After replacing the air flowmeter, the condition of the car improved slightly, but the fault was still there. Check again and find that the 4th cylinder spark plug is covered with gasoline, indicating that the cylinder is not working.
The engine has serious carbon accumulation. The most common cause of idling jitter is excessive carbonisation of the throttle valve or fuel nozzle.
The solutions to unstable idle speed, shaking, shaking and black smoke are as follows: the engine is seriously carbonized. The common cause of car shaking is that the throttle valve is too dirty or the fuel nozzle has too much carbon.Solution: Clean the oil road and check whether there is carbon in the idle motor, which should be cleaned.
The control unit receives the wrong signal and sends the wrong instruction, causing the engine idling intake control to be inaccurate, causing the engine to burn abnormally, which is an indirect cause of unstable idle speed. Common causes are: air flow meter or its line failure; intake pressure sensor or its line failure; engine control unit plug due to poor contact with water inlet or internal computer failure.
Engine ignition order is 2; that is to say, when cylinder 1 is doing work, cylinder 3 is in a compressed state, cylinder 4 is in the intake state, and cylinder 2 is in the exhaust state. Status.
People sit in the cab, and the order of the cylinder is: 5 on the right, and 6 on the left.In this case, the ignition order is: 1-4-5-2-3-6.
The ignition order of the engine is 2; that is, when the 1st cylinder is in the "work", the 3rd cylinder is in the "compression" state, the 4th cylinder is in the "ink-ink" state, and the 2nd cylinder is in the "exhaust" state. Depending on the number of engine cylinders, the ignition order of the engine will also vary.
Engine carbon accumulation problem, the engine will accumulate some carbon accumulation after a period of use, which will cause engine damage, difficulty in starting, poor acceleration, starting The machine is too noisy and other phenomena. Mixed gas combustion is poor and gas combustion is insufficient. Sensor problem. Multiple sensors are aging. If the owner does not add oil as required, it will lead to accelerated engine wear and abnormal operation in the long run, and the engine fault light will turn on. Generally, replacing the oil with the corresponding conditions can eliminate the fault light. The reasons why the engine fault light is on are engine carbonisation problems, poor combustion of mixed gas, sensor problems, maintenance problems and oil quality problems.Car owners need to regularly clean the carbon accumulation of the engine, check the working condition of the sensor, maintain it regularly, and use qualified oil products. The fuel quality is poor and does not meet the standard.
Global trade certificate verification
author: 2024-12-25 00:58How to use data for HS code classification
author: 2024-12-25 00:45How to ensure transparency in supply chains
author: 2024-12-25 00:39How to benchmark HS code usage
author: 2024-12-24 23:20Pulp and paper HS code compliance
author: 2024-12-24 22:23HS code integration with supply chain
author: 2024-12-25 01:01Comparative HS code duty analysis
author: 2024-12-25 00:27HS code alignment with sustainability targets
author: 2024-12-24 22:56How to forecast seasonal import demands
author: 2024-12-24 22:51Carbon steel HS code references
author: 2024-12-24 22:21682.23MB
Check651.11MB
Check356.89MB
Check778.38MB
Check562.94MB
Check788.72MB
Check191.26MB
Check383.72MB
Check591.63MB
Check276.37MB
Check795.74MB
Check533.35MB
Check114.91MB
Check137.23MB
Check159.74MB
Check221.96MB
Check258.27MB
Check621.45MB
Check627.82MB
Check429.75MB
Check789.75MB
Check263.62MB
Check891.76MB
Check643.39MB
Check827.56MB
Check518.65MB
Check657.49MB
Check596.33MB
Check939.44MB
Check969.87MB
Check911.96MB
Check613.88MB
Check336.52MB
Check816.52MB
Check129.57MB
Check483.14MB
CheckScan to install
Commodity price indexing by HS code to discover more
Netizen comments More
571 Global import export data subscription
2024-12-25 00:52 recommend
1705 How to track global shipments
2024-12-25 00:50 recommend
2058 HS code compliance for African Union members
2024-12-25 00:36 recommend
387 Global supply chain risk assessment
2024-12-25 00:10 recommend
299 Comparing international shipping carriers
2024-12-24 23:36 recommend