Trade data-driven cost modeling

List of Contents of this article:

• 1, What to do if the Baoyuan system cannot recognize the macro program
• 2, Is the Baoyuan system a gong or something?
• 3、 What to do if it's too troublesome to import files in the Baoyuan system
• 4, How to retrieve the lost origin of the treasure element system
• 5, How to connect Baoyuan engraving and milling machine M-500I system to computer
• 6, Baoyuan system zero setting parameter

What to do if the Baoyuan system cannot recognize macro programs

Position control ring alarm: It may be that the measurement loop is open, the measurement system is damaged, and the internal bit control unit is damaged. It moves without giving instructions, which may be excessive drift, positive feedback, bit control unit failure; measurement components are damaged.

It is recommended to read the instruction manual and check the alarm information form. The possible reason is that the power was cut off when the tower was not in place. After turning on the power, it was detected that the tower was in an abnormal state, so the alarm was called. You can rotate the tower manually, and the alarm can be eliminated by turning the tower.

Baoyuan injection molding machine control system program setting steps: In the controller of the injection molding machine, set the installation detection program and installation debugging parameters. During the installation process of the injection molding machine, the injection molding machine's own sensors and detection lines and additional testing equipment are used for installation.

The solution to the problem that the soft limit parameter of the Baoyuan system does not respond is as follows: the soft stroke limit fails to modify the X-axis positive parameter of the soft limit, and make it appropriately larger to solve the problem.

If the driver of the Baoyuan system r42 is in an alarm state, change the axial direction of the driver to determine whether there is a problem with the motor and power line. At this time, you need to find the maintenance technician of the Baoyuan system to test and deal with it.

The hardware contact of the Baoyuan system is set as follows: enter the main interface of the Baoyuan system after power-on. Click the "SETUP" button on the screen, and the system will enter the setting menu.

Is the Baoyuan system a gong or something?

1. Baoyuan is a kind of numerical control system in Taiwan. Precision System Control of Baoyuan Technology was founded in November 2000. It is a department under Baoyuan Technology, a subsidiary of Baocheng International Group established in 1993.

2. The new generation system is a Taiwan system, which can be equipped on lathes, milling machines, grinding machines and special tools. Machine tool (English name: machine tool) refers to the machine that manufactures the machine, also known as the working mother machine or tool machine, which is usually abbreviated as machine tool. It is generally divided into metal cutting machine tools, forging machine tools and woodworking machine tools, etc.

3. As a system in Taiwan, Baoyuan CNC System believes that many people in southeast China should have some impressions. Such large CNC manufacturers basically have their own agents, otherwise an enterprise can't do it in after-sales service.

4. These two systems are actually similar. The Guangshu system is currently the best-selling system in China, but because of the contract with state-owned enterprises, state-owned enterprises use it more.The new generation of Baoyuan is a system from Taiwan. Baoyuan has not developed well in recent years and has been acquired by Yanhua, with a low market share.

5. The most widely used CNC opening machine in the extreme East is the new generation system, Baoyuan system, Weihong system and Shanlong system; among them, the new generation and Baoyuan system are developed and produced in Taiwan, the Weihong system is in Shanghai, and the Shanlong system is in Shenzhen.

6. Among them, the new generation and Baoyuan system are developed and produced in Taiwan, the Weihong system is in Shanghai, and the Shanlong system is in Shenzhen. Each system has different functions because of different prices.

What should I do if the Baoyuan system is too troublesome to import files

1. To make a USB disk boot disk with cabbage or old Maotao software. THEN COPY THE WIN7 SYSTEM TO THE USB FLASH SK.Restart the computer to enter the BIOS program settings, find the pin startup program item and set it to the USB flash drive to start. Exit the BIOS program and select Save Settings to exit.

2. The official of the Baoyuan system platform said that the Baoyuan system will not fail to fail to transfer files under the condition that the network is stable. The failure means that the network connection is unstable, and the network needs to be replaced to solve it.

3. Support, the method is as follows: method to select the file, right-click-copy (shortcut Ctrl+C)-enter disk D-right-click paste (shortcut: Ctrl+V). The method is to open the C disk and the D disk, select the file, hold down the left button - drag from the C disk to the D disk. Method: Use the resource manager to drag from disk C to disk D.

How to retrieve the lost origin of the Baoyuan system

The Baoyuan system alarm can't find the reference point because the zero switch of the machine tool has been bumped and shifted. When returning to zero, the zero signal is not correct and the Baoyuan system cannot return to the origin. The alarm Z axis is an external problem on the origin gear block. Check whether the travel switch of the origin gear block is blocked.

The method of setting parameters to zero in the Baoyuan system is as follows: enter the program interface of the Baoyuan system. Select the "Parameters" menu and enter the "Zero Settings" interface. In the "Zero Return Settings" interface, set the zero return mode and zero return speed and other parameters of each axis.

May I ask if the machine tool needs to return to zero when it is turned on? If you need to return to zero, if the servo motor is replaced, it can return to zero, but there must be an error with the original mechanical origin.

The lost recovery method is as follows: enter the repair menu.Press the repair key in manual mode to enter the repair menu. Enter the axis configuration screen. Press the ATC project key or F0 key to enter the axis configuration screen.

How to connect the Baoyuan engraving and milling machine M-500I system to the computer

1. This problem should be because cnc cannot work offline. Must work online with the computer. So you can't surf the Internet while working.

2. The method of connecting the m6500 printer to the computer is as follows: First, search the official website of Pentu online, find the service and support options on the official website interface, click the support and download options, search for the printer model, select the computer operating system, click download, and then match and connect.

3. The transmission method is as follows: make sure that the computer is connected to the Frank 0i-mf system.You can use an appropriate data cable (such as a USB cable) to connect the computer to the Frank 0i-mf system. Open the control panel of the Frank 0i-mf system.

Baoyuan system return to zero setting parameters

The parameters under the engraving machine I/Q status window are disordered. At this time, the parameters need to be modified. The method is as follows: click the x axis, and press ctrl+shift+alt at the same time and then right-click to pop up After the window, click "reverse the extreme direction of the point". Click the y-axis, press ctrl+shift+alt at the same time and then right-click. After the pop-up window, click "reverse the pole of the point".

Baoyuan injection molding machine control system program setting steps: In the controller of the injection molding machine, set the installation detection program and installation debugging parameters.During the installation process of the injection molding machine, the injection molding machine's own sensors and detection lines and additional testing equipment are used for installation.

Generally speaking, the control system of the machine tool will provide corresponding parameter settings to adjust the compensation value. When setting the radius compensation of the Baoyuan system, the following steps are generally required: Determine the compensation direction: Determine the direction of compensation according to the needs and actual situation of workpiece processing, that is, the direction of the X axis or Z axis in the machine tool coordinate system.