HS code classification for electronics

List of the contents of this article:

• 1,The reason and solution of win7 computer always blue screen
• 2, How to solve the blue screen when installing win7
• 3, win7 starts up with a blue screen, what should I do? ( As shown in the picture)
• 4 、win7 starts to the blue screen after starting windows, and then restarts

The reason and solution for the blue screen of the win7 computer

1. You can uninstall or disable them in safe mode. Virus inspection such as shock wave and oscillation wave and some Trojan spyware will cause Win7 blue screen and sometimes lead to crash, so checking for viruses is a necessary step. You can use relevant tools to scan the computer for viruses.

2. Restart. First, write down the blue screen error code, and then restart.Some blue screens may be caused by a momentary error in the software system. After restarting and initializing, the software system will work normally.

3. If there is a device, try to delete it first, restart the computer, and Win9X will automatically adjust. General problems can be solved. If not, you can manually adjust or upgrade the corresponding driver. Software causes and solutions of "blue screen" Hardware is closely related to software, and sometimes software also contributes to the phenomenon of "blue screen".

4. Computer blue screen is a common operating system error, which may be caused by a variety of reasons, including hardware problems, driver problems, system vulnerabilities and malware.

5. How to solve the sudden blue screen of Win7 computer. The steps are as follows: restart the computer. If the blue screen only appears occasionally, we just need to restart the computer;A BUG with Windows XP itself.

6. The blue screen of the computer is a very common fault, and the blue screen failure of the win7 system is even more frequent. This kind of failure will annoy users, because it will lead to the loss of important work data or seriously affect work efficiency, so it is very necessary to solve the win7 blue screen problem in time.

How to solve the blue screen when installing win7 startup

1. Solution: clean up the dust in the chassis, unplug the memory stick, wipe the gold finger with an eraser, and then plug it tightly again.

2. Analysis and solution of the reasons for the blue screen of the computer installed in the win7 system: open the chassis to clean up after the power is cut off.Dust, check all connections, especially the memory stick, unplug the memory, clean up the plug and plug it back in; if it is an independent graphics card network card, the same method should be handled.

3. First, open "Computer Butler" and search for "windog" software, as shown in the figure below: then click the "Complete" option.

4. Restart the computer, press F8, and the selection menu will appear. Select the last correct configuration and try the safe mode. If you can enter the safe mode, you can uninstall the recently installed software or driver. If you can enter safe mode, you can fix the blue screen through the computer butler.

5. Now I will introduce how to solve the blue screen restart of win7 startup.

6. In general,The blue screen appears after updating the hardware driver or adding new hardware and installing its driver. At this time, the last correct configuration provided by Win7 is the shortcut to solve the blue screen. Restart the system. Press the F8 key when the boot menu appears. The advanced boot options menu will appear, and then select the last correct configuration.

win7 starts up with a blue screen, what should I do? ( As shown in the figure)

1. If the screen is still blue in the process of entering the safe mode, then there may be a hardware problem. If it is a desktop computer, please clean up the dust in the chassis and plug and unplug the memory again. If there are two memories, try one for the time being. If it is a notebook, it is recommended to go to the after-sales department for testing.

2. If you don't have time to find and analyze the cause of the blue screen, you can redo the system after backing up the file. In this way, the problem can be solved simply and thoroughly.

3. The specific method is as follows: in the main interface of bios, press the F7 key---boot (start) to set the CSM item to ENABLED to open. Press F10 to save and exit.

4. If you can enter the security center, it means that there is a conflict or software problem with the mobile phone software, that is, the system can be remade. When the computer's blue screen enters safe mode, there may be common failures in the hardware configuration, that is, you must open the host box to check the hardware configuration.

win7 to the blue screen after starting windows, and then restart

1. The rest is a problem, just fix it, which is also one of the few blue screen codes that can be repaired. The repair method is to find the original system installation disk (or the pe boot interface of Golden Finger V6 with console repair).

2. The computer startup is stuck in the blue screen of "Starting Windows", which is mainly caused by: "memory error" or "abnormal shutdown".This is the solution: turn on the power. After the "windows" interface, press F8 and return. Enter the safe mode, advanced startup options, the last correct configuration, and enter.

3. This is a system failure, which may be caused by viruses or hardware driver mismatch. It is recommended to reinstall the pure version of the system, which is the most stable and safest.

4. Then it is likely that poor heat dissipation causes the computer to have a blue screen. The solution is that if it is caused by the temperature of the CPU or graphics card, turn on the CPU fan and the graphics card fan to see if the graphics card fan rotate normally. If it is normal, it is recommended to strengthen the heat dissipation of the host, such as adding chassis heat dissipation, etc. If the temperature of the hard disk is too high, there may be a hard disk failure and need to be replaced.

5. Open the old Maotao software on the computer, then click the "Start" option first, and then click the "Write to Hard Disk Image" option again;Select the Windows7 image file in the image file, select the "Write" option, and wait for a period of time. After the writing is completed, the USB disk boot disk will be completed.